Saturday, April 2, 2016

The End: Spitfire PR.IG

"This is the End, beautiful friend."

The Spitfire PR.IG story has reached the end.
Over the many months and through trials and tribulations.
Many disappointments, and small victories.
This Spitfire remains where it is and where it always will be.

The tone of the opening verse was a little more serious than I was going for, but I'll just leave it there and segue without a real segue into what this post is about. Weathering and final assembly. Can a segue be a segue in itself?


Dark dirt wash
The underside all nice and clean.


Look I haven't broken the pitot tube yet!

Dark dirt wash
I added a little UMP Dark Dirt wash here as a test.

Dark dirt wash
With a damp paper towel it just wipes off.

Dark dirt wash
This could go great or very, very badly.

Dark dirt wash
Before I took the plunge on the topside. I had some rougher areas I was concerned about, but I just went with it to see how it turned out. The rougher areas were near the wing root and on the elevators. You can't think and ponder forever.

Dark dirt wash

Dark dirt wash
After a lot of rubbing and wiping with damp paper towels and Q-tips. The areas that were a little rough were a bit difficult to clean up. I had some discolored areas that I can't explain. If the gloss coat was flawless, this method probably would have worked out better. I'm on the fence about it at the moment. Maybe I should have just used it as a pin wash and not put it all over? Maybe I should have gone with an enamel wash? Maybe I need a different gloss coat? Maybe the paint job was too rough?

Finishing touches

Finishing touches

Finishing touches
Attached landing gear.

Finishing touches
At last, in the final stages and now on its own three feet! The canopy didn't turn out as nice as I had hoped. I don't know what happened to the front windscreen, there is some paint damage or something I can't get rid of.

Finishing touches
Almost there....


Now for the moment you've all been waiting for, the final pictures of the PR.IG.


"This is the End... of our elaborate plans."


0330162041c

0330162042d

0330162042a

0330162041a

0330162040e

0330162040b

0330162040a

0330162042

0330162041e
The finish coat was done with Winsor Newton Satin acrylic varnish. It came out a little more matte than I was hoping. Maybe I put it down to heavy? Maybe that's what it should look like?


Let's see if I can remember some things I learned.
  • I'm done with AK primer. I think this may be part of my paint roughage problem.
  • I'm suspicious of Model Master Acryl paint for covering large areas. The coagulation I experienced with the custom mix shouldn't have happened.
  • I'm dubious about the value of pre-shading. I may explore other techniques.
  • Perhaps the entire model should have been coated with pink and a camo-tint pink applied on top. Coverage with a white based paint is quite challenging. If I had to do over, I would use Tamiya white and red or something else.
  • I'm not sure how necessary the bottom resin piece was. Next time I try this again, I will drill holes for the lower cameras and build something behind it.
  • Along with the above bullet, I'll use a clay or Milliput to craft the extra gas tank and cameras. They are mostly internal and what you see is very limited.....how hard can it be?
  • Milliput is actually really great for gap filling, not so much for scribing, but a layer of CA can assist with that.
  • I think I will buy resin seats for almost every kit I do.
  • Humbrol Maskol does get weird and leave marks on clear parts if you leave it there for months.
  • I think I dropped the elevators too much. Next time I'll do a little more research and reduce the hang.
  • All the little PE I added to the interior of the cockpit, tough to see....but I know it's there.
  • I don't know why it's so hard to find bigger pin vise bits.
  • I need another Spitfire.

That's it, this project is wrapped up as far as I'm concerned as it's been dragging on since July 2015. It's nice to have this off the shelf so I can focus on other things. I've already got my eye on getting another Tamiya kit so I can build another PR.IG, but this time it will be a bare metal finish.

"This is the Ennnnnnnnnnd."

2 comments: